LK Automation Limited
Brand:
Yaskawa
SGD7S-2R8A20A002 Single axis servo driver
Yaskawa SGD7S-2R8A20A002 Manual And Instructions
SGD7S-2R8A20A002 datasheetPDF datasheet
SGD7S-2R8A20A002 Communications ReferencesInstruction Guide
SGD7S-2R8A20A002 MECHATROLINK-III CommunicationsINSTRUCTION SHEET
Yaskawa SGD7S-2R8A20A002 Product information and technical parameters：
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-2R8A20A002
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown
...More relevant models >>>>
SGD7S-2R8A20A002 datasheetPDF datasheet
SGD7S-2R8A20A002 Communications ReferencesInstruction Guide
SGD7S-2R8A20A002 MECHATROLINK-III CommunicationsINSTRUCTION SHEET
Yaskawa SGD7S-2R8A20A002 Product information and technical parameters：
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-2R8A20A002
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 15Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load SGD7S-2R8A20A002.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGD7S-2R8A20A002
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -v series servo unit SGDV SGD7S-2R8A20A002.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Optional (hardware): DB resistance external type.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGD7S-2R8A20A002.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.6Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control cirrcuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGD7S-2R8A20A002.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGD7S-2R8A20A002.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Rated speed: 1500r\/min.
Power: 15Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load SGD7S-2R8A20A002.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGD7S-2R8A20A002
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -v series servo unit SGDV SGD7S-2R8A20A002.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Optional (hardware): DB resistance external type.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGD7S-2R8A20A002.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.6Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control cirrcuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGD7S-2R8A20A002.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGD7S-2R8A20A002.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>