LK Automation Limited
Brand:
Yaskawa
SGMSV-70ADA2S servo motor
Yaskawa SGMSV-70ADA2S Manual And Instructions
SGMSV-70ADA2S Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-70ADA2S Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-70ADA2S
Sigma -V series servo motor SGMSV.
Rated output: 7.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMSV-70ADA2S Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-70ADA2S Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-70ADA2S
Sigma -V series servo motor SGMSV.
Rated output: 7.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -V series servo motor SGMJV.
Rated output: 0.2KW (200W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with hold brake (DC24V).
Medium inertia.
Instantaneous maximum torque (rating 350%) SGMSV-70ADA2S.
Equipped with a high resolution serial encoder (13\/20 bit).
Max speed up to 6000r\/min SGMSV-70ADA2S
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above SGMSV-70ADA2S.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMSH type SGMSV-70ADA2S.
Rated speed: 3000r\/min.
Power: 3.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the inittial contact, can also be completed in a short time the best set SGMSV-70ADA2S.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regeneerative resistance connection terminals SGMSV-70ADA2S.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor
Rated output: 0.2KW (200W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with hold brake (DC24V).
Medium inertia.
Instantaneous maximum torque (rating 350%) SGMSV-70ADA2S.
Equipped with a high resolution serial encoder (13\/20 bit).
Max speed up to 6000r\/min SGMSV-70ADA2S
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above SGMSV-70ADA2S.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMSH type SGMSV-70ADA2S.
Rated speed: 3000r\/min.
Power: 3.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the inittial contact, can also be completed in a short time the best set SGMSV-70ADA2S.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regeneerative resistance connection terminals SGMSV-70ADA2S.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor
...More relevant models >>>>