LK Automation Limited
Brand:
Yaskawa
SGMSV-30D3A2D servo motor
Yaskawa SGMSV-30D3A2D Manual And Instructions
SGMSV-30D3A2D Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-30D3A2D Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-30D3A2D
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMSV-30D3A2D Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-30D3A2D Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-30D3A2D
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -7 series servo unit SGD7S.
Maximum applicable motor capacity: 0.75kW.
Voltage: single phase \/ three phase AC200V.
Interface: analog voltage, pulse sequence.
Design sequence: A.
Hardware purchase: rack installation specifications.
Select servo.
Since the Yaskawa since the beginning of 1992 sales of sigma series, has always attached great importance to technical exchanges and customer,
In order to solve the new problem of customer machinery, and repeatedly to carry out technical innovation SGMSV-30D3A2D SGMSV-30D3A2D
High speed, high accuracy, the use of convenience in recent years has been the requirement of customers,
But the degree of its requirement is continuously deepening.
2014, the servo drive upgrade to have 7 major advantages",
Provide solutions for customers unique yaskawa SGMSV-30D3A2D.
With its excellent performance, convenient operation, long life cycle, etc.,
In all these areas will have great potential, provides solutions to the shocking. "Choose servo, choose"Full closed loop module.
Maximum applicable motor capacity: 0.05kw.
Power supply voltage: three phase AC200V.
Interface: analog voltage, pulse sequence type (rotary servo motor) SGMSV-30D3A2D.
Design sequence: B.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating). Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 3kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMSV-30D3A2D.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMSV-30D3A2D.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Maximum applicable motor capacity: 0.75kW.
Voltage: single phase \/ three phase AC200V.
Interface: analog voltage, pulse sequence.
Design sequence: A.
Hardware purchase: rack installation specifications.
Select servo.
Since the Yaskawa since the beginning of 1992 sales of sigma series, has always attached great importance to technical exchanges and customer,
In order to solve the new problem of customer machinery, and repeatedly to carry out technical innovation SGMSV-30D3A2D SGMSV-30D3A2D
High speed, high accuracy, the use of convenience in recent years has been the requirement of customers,
But the degree of its requirement is continuously deepening.
2014, the servo drive upgrade to have 7 major advantages",
Provide solutions for customers unique yaskawa SGMSV-30D3A2D.
With its excellent performance, convenient operation, long life cycle, etc.,
In all these areas will have great potential, provides solutions to the shocking. "Choose servo, choose"Full closed loop module.
Maximum applicable motor capacity: 0.05kw.
Power supply voltage: three phase AC200V.
Interface: analog voltage, pulse sequence type (rotary servo motor) SGMSV-30D3A2D.
Design sequence: B.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating). Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 3kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMSV-30D3A2D.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMSV-30D3A2D.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>