LK Automation Limited
Brand:
Yaskawa
SGMSV-20DDA2C servo motor
Yaskawa SGMSV-20DDA2C Manual And Instructions
SGMSV-20DDA2C Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-20DDA2C Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-20DDA2C
Sigma -V series servo motor SGMSV.
Rated output: 2.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMSV-20DDA2C Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-20DDA2C Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-20DDA2C
Sigma -V series servo motor SGMSV.
Rated output: 2.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Matching (hardware): paint.
With the latest technology to pursue the use of convenience.
The use of new non adjustment function, no need to adjust SGMSV-20DDA2C.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed SGMSV-20DDA2C
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start.
Achieve a high response 1kHz above SGMSV-20DDA2C.
Equipped with a new advanced automatic tuning function.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control.Servo motor type SGMAH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw SGMSV-20DDA2C.
Optional parts: with DC90V brake.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenanceSingle axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be diisplayed SGMSV-20DDA2C.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and promptt the change of time on the screen SGMSV-20DDA2C.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Matching (hardware): paint.
With the latest technology to pursue the use of convenience.
The use of new non adjustment function, no need to adjust SGMSV-20DDA2C.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed SGMSV-20DDA2C
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start.
Achieve a high response 1kHz above SGMSV-20DDA2C.
Equipped with a new advanced automatic tuning function.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control.Servo motor type SGMAH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw SGMSV-20DDA2C.
Optional parts: with DC90V brake.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenanceSingle axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be diisplayed SGMSV-20DDA2C.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and promptt the change of time on the screen SGMSV-20DDA2C.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown
...More relevant models >>>>