LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGMSV-15DDA61 servo motor
Yaskawa SGMSV-15DDA61 Manual And Instructions
SGMSV-15DDA61 Setup Rotational MotorUSER'S MANUAL

Yaskawa SGMSV-15DDA61 Product information and technical parameters:
Brand: Yaskawa
Name: servo motor
Model: SGMSV-15DDA61
Sigma -V series servo motor SGMSV.
Rated output: 1.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Single axis servo driver SGD7S.
Maximum applicable motor capacity: 1.5kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ᥹఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified SGMSV-15DDA61.
No need to write parameters in the device assembly site, can reduce the equipment delivery time SGMSV-15DDA61
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed SGMSV-15DDA61.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdownSGMMV type of small capacity servo motor SGMSV-15DDA61.
Rated output: 5.5W.
Voltage: DC24V/DC48V.
Serial encoder: 17 bit absolute value type.
Design sequence: standard.
Shaft end: straight shaft, with flat seat (optional parts).
Optional parts: do not buy pieces.
Ultra small, ultra small capacity
Flange size 15mm:3.3 ~ 11W.
Flange size 25mm:10 ~ 30W.
Is equipped with a high resolution absolute value serial encoder (17 bit).
Can also be used as an incremental.
Max speed up to 6000r/min.
Type is complete (there are 2 kinds of flange size, DC/AC power supply voltage, with hold brake).











Servo motor type SGMAH (speed: 3000r\/min).
Power: 30W.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw.
Optional parts: with oil seal.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting aand maintenance time is shortened SGMSV-15DDA61.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanicall characteristics SGMSV-15DDA61.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance


...More relevant models >>>>