LK Automation Limited
Brand:
Yaskawa
SGMPS-08ACE21E Medium inertia flat type motor
Yaskawa SGMPS-08ACE21E Manual And Instructions
SGMPS-08ACE21E Setup Rotational MotorProduct Manual
Yaskawa SGMPS-08ACE21E Product information and technical parameters：
Brand: Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-08ACE21E
Sigma -V series servo motor SGMPS.
Rated output: 750W (0.75kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMPS-08ACE21E Setup Rotational MotorProduct Manual
Yaskawa SGMPS-08ACE21E Product information and technical parameters：
Brand: Yaskawa
Name: Medium inertia flat type motor
Model: SGMPS-08ACE21E
Sigma -V series servo motor SGMPS.
Rated output: 750W (0.75kw).
Power supply voltage: AC200V.
Serial encoder: 17 bit Delta (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, D24V brake.
Partial flat series: the need to install the servo motor in a small space SGMPS-08ACE21E.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products SGMPS-08ACE21E
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters SGMPS-08ACE21E.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorServo motor type SGMAH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key SGMPS-08ACE21E.
Optional parts: with DC90V brake.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenanceLarge capacity SGMVV type servo motor.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (without keyway and screw).
Optional parts: keep the brake (DC90V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGMPS-08ACE21E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, D24V brake.
Partial flat series: the need to install the servo motor in a small space SGMPS-08ACE21E.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products SGMPS-08ACE21E
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters SGMPS-08ACE21E.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorServo motor type SGMAH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key SGMPS-08ACE21E.
Optional parts: with DC90V brake.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenanceLarge capacity SGMVV type servo motor.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (without keyway and screw).
Optional parts: keep the brake (DC90V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGMPS-08ACE21E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
...More relevant models >>>>