LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGMPH-01AAA4E Servo motor

Yaskawa SGMPH-01AAA4E Product information and technical parameters:
Brand: Yaskawa
Name: Servo motor
Model: SGMPH-01AAA4E
Servo motor type SGMPH (speed: 3000r/min).
Power: 0.1kw.
Power supply voltage: single phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: with oil seal, DC24V brake.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated.

Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC24V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMPH-01AAA4E SGMPH-01AAA4E
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -V series servo motor SGMSV SGMPH-01AAA4E.
Rated output: 1.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) SGMPH-01AAA4E.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor type SGMPH (speed: 3000r\/min).
Power: 0.4kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft without key.
Optional parts: no brake oil seal.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 1000V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer SGMPH-01AAA4E.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a veery seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated


...More relevant models >>>>
Related download