LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGMPH-01A1A21 Servo motor

Yaskawa SGMPH-01A1A21 Product information and technical parameters:
Brand: Yaskawa
Name: Servo motor
Model: SGMPH-01A1A21
Servo motor type SGMPH (speed: 3000r/min).
Power: 0.1kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: no brake oil seal.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated.

Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with hold brake (DC24V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMPH-01A1A21 SGMPH-01A1A21
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -V series servo motor SGMGV SGMPH-01A1A21.
Rated output: 2.9kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake) SGMPH-01A1A21.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMPH-01A1A21.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMPH-01A1A21.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.


...More relevant models >>>>
Related download