LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGMGV-75D3C6C Rotary servo motor
Yaskawa SGMGV-75D3C6C Manual And Instructions
SGMGV-75D3C6C Setup Rotational MotorUSER'S MANUAL

Yaskawa SGMGV-75D3C6C Product information and technical parameters:
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-75D3C6C
Sigma -V series servo motor SGMGV.
Rated output: 7.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Servo motor type SGMPH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit relative value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space SGMGV-75D3C6C.
Flexible user system.
For you to build the best system to enrich the product line to support you SGMGV-75D3C6C
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedSigma -v series servo unit SGDV SGMGV-75D3C6C.
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard) SGMGV-75D3C6C.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMGV-75D3C6C.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMGV-75D3C6C.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.


...More relevant models >>>>