LK Automation Limited
Brand:
Yaskawa
SGMGV-20A3A6D Rotary servo motor
Yaskawa SGMGV-20A3A6D Manual And Instructions
SGMGV-20A3A6D Setup Rotational MotorProduct Manual
Yaskawa SGMGV-20A3A6D Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-20A3A6D
Sigma -V series servo motor SGMGV.
Rated output: 1.8kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMGV-20A3A6D Setup Rotational MotorProduct Manual
Yaskawa SGMGV-20A3A6D Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-20A3A6D
Sigma -V series servo motor SGMGV.
Rated output: 1.8kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.05kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control SGMGV-20A3A6D SGMGV-20A3A6D Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time SGMGV-20A3A6D.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMGV-20A3A6D. Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC90V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.85kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGV-20A3A6D.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMGV-20A3A6D.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Maximum applicable motor capacity: 0.05kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control SGMGV-20A3A6D SGMGV-20A3A6D Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time SGMGV-20A3A6D.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMGV-20A3A6D. Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC90V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.85kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGV-20A3A6D.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMGV-20A3A6D.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>