LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGMGV-09DDA6S Rotary servo motor
Yaskawa SGMGV-09DDA6S Manual And Instructions
SGMGV-09DDA6S Setup Rotational MotorUSER'S MANUAL

Yaskawa SGMGV-09DDA6S Product information and technical parameters:
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-09DDA6S
Sigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

High performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 1.0kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK-II communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Function: pressure feedback control function SGMGV-09DDA6S.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models SGMGV-09DDA6S
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device SGMGV-09DDA6S.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller SGMGV-09DDA6S. Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r/min.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen.







Equipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: single phase AC100V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): base mounting type (standard).
Matching (software): standard.
Matching (parameter): standard.
Optional module: INDEXER+ full closed loop module.
Simple.
By programming and serial programming, easy implementation of motion control.
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table.
The maximum number of progrrammable positioning points to 256 points SGMGV-09DDA6S.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy. SGMGV-09DDA6S.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller.


...More relevant models >>>>