LK Automation Limited
Brand:
Yaskawa
SGMGV-09ADC6C Rotary servo motor
Yaskawa SGMGV-09ADC6C Manual And Instructions
SGMGV-09ADC6C Setup Rotational MotorProduct Manual
Yaskawa SGMGV-09ADC6C Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-09ADC6C
Sigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMGV-09ADC6C Setup Rotational MotorProduct Manual
Yaskawa SGMGV-09ADC6C Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-09ADC6C
Sigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Optional (hardware): rack mounting type.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGMGV-09ADC6C SGMGV-09ADC6C
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time SGMGV-09ADC6C.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMGV-09ADC6C. Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.3kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Function: fixed point through output function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rootation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMGV-09ADC6C.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGMGV-09ADC6C.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Optional (hardware): rack mounting type.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGMGV-09ADC6C SGMGV-09ADC6C
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time SGMGV-09ADC6C.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMGV-09ADC6C. Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.3kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Function: fixed point through output function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rootation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMGV-09ADC6C.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGMGV-09ADC6C.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.
...More relevant models >>>>