LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGMGV-09A3C61 Rotary servo motor
Yaskawa SGMGV-09A3C61 Manual And Instructions
SGMGV-09A3C61 Setup Rotational MotorProduct Manual

Yaskawa SGMGV-09A3C61 Product information and technical parameters:
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-09A3C61
Sigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 1.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Key: straight shaft end uranium belt with screw.
Optional parts: with oil seal, DC90V brake.
Ultra high power response series: the need for small inertia, high torque SGMGV-09A3C61.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain SGMGV-09A3C61
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals SGMGV-09A3C61.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorLarge capacity SGMVV type servo motor.
Rated output: 45KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw).
Optional parts: with hold brake (DC24V) SGMGV-09A3C61.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenFull closed loop module.
Maximum applicable motor capacity: 5.0kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMGV-09A3C61.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed onn the side of the machine to realize the high precision and high response SGMGV-09A3C61.
External encoder capable of corresponding high resolution (linear grating).


...More relevant models >>>>