LK Automation Limited
Brand:
Yaskawa
SGMGV-05DDC2D Rotary servo motor
Yaskawa SGMGV-05DDC2D Manual And Instructions
SGMGV-05DDC2D Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMGV-05DDC2D Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-05DDC2D
Sigma -V series servo motor SGMGV.
Rated output: 450W (0.45KW).
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMGV-05DDC2D Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMGV-05DDC2D Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-05DDC2D
Sigma -V series servo motor SGMGV.
Rated output: 450W (0.45KW).
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load SGMGV-05DDC2D.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGV-05DDC2D
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor type SGMAH (speed: 3000r\/min) SGMGV-05DDC2D.
Power: 30W.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with DC90V brake.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response SGMGV-05DDC2D.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenanceSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 2kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMGV-05DDC2D.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMGV-05DDC2D.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Rated speed: 1000r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load SGMGV-05DDC2D.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMGV-05DDC2D
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor type SGMAH (speed: 3000r\/min) SGMGV-05DDC2D.
Power: 30W.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with DC90V brake.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response SGMGV-05DDC2D.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenanceSigma -v series servo unit SGDV.
Maximum applicable motor capacity: 2kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMGV-05DDC2D.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMGV-05DDC2D.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>