LK Automation Limited
Brand:
Yaskawa
SGMGH-30ACC3D Motor for high precision machine tool
Yaskawa SGMGH-30ACC3D Product information and technical parameters：
Brand: Yaskawa
Name: Motor for high precision machine tool
Model: SGMGH-30ACC3D
Servo motor SGMGH type.
Rated speed: 1500r/min.
Power: 2.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1/10, with parallel key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control.
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 3kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGMGH-30ACC3D SGMGH-30ACC3D
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time SGMGH-30ACC3D.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMGH-30ACC3D. Sigma -V series servo motor SGMPS.
Rated output: 400W (0.4KW).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Innstallation method: flange type SGMGH-30ACC3D.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-30ACC3D.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Maximum applicable motor capacity: 3kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGMGH-30ACC3D SGMGH-30ACC3D
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time SGMGH-30ACC3D.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGMGH-30ACC3D. Sigma -V series servo motor SGMPS.
Rated output: 400W (0.4KW).
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP67 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V).
Corresponding to the RoHS instruction: in accordance with the RoHS directive.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1.5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Innstallation method: flange type SGMGH-30ACC3D.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-30ACC3D.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Related download