LK Automation Limited
Brand:
Yaskawa
SGMGH-09A2B3B servo motor
Yaskawa SGMGH-09A2B3B Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMGH-09A2B3B
Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Type: SGDH type drive.
Capacity: 5.0kw.
Voltage: three phase 400V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor SGMGH-09A2B3B.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer SGMGH-09A2B3B
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data SGMGH-09A2B3B. Sigma -V series servo motor SGMGV.
Rated output: 5.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V) SGMGH-09A2B3B.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGMGH-09A2B3B.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-09A2B3B.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Capacity: 5.0kw.
Voltage: three phase 400V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor SGMGH-09A2B3B.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer SGMGH-09A2B3B
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data SGMGH-09A2B3B. Sigma -V series servo motor SGMGV.
Rated output: 5.5kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with hold brake (DC24V) SGMGH-09A2B3B.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGMGH-09A2B3B.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-09A2B3B.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Related download