LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGMCS-45E3B11 Direct drive servo motor
Yaskawa SGMCS-45E3B11 Manual And Instructions
SGMCS-45E3B11 Setup Rotational MotorUSER'S MANUAL

Yaskawa SGMCS-45E3B11 Product information and technical parameters:
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-45E3B11
Capacity type of direct drive servo motor SGMCS.
Rated torque: M \/ 45N.
Servo motor outside diameter size: 290mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the size of the outer diameter of the service motor is marked as E model.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Capacity rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation

Large capacity servo unit.
Maximum applicable motor capacity: 30KW.
Power supply voltage: three phase AC400V.
Fastening: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: B.
Optional parts (hardware): ventilation duct installation type.
Improve the performance of large torque transmission machinery!
Vibration suppression function SGMCS-45E3B11.
When the driving system of the machine is vibrating, the observer is used to reduce the vibration and suppress the vibration of the device SGMCS-45E3B11
Friction compensation function.
Even when the load fluctuation, the gain can be suppressed without changing the position deviation.
Therefore, the overshoot can be suppressed to ensure the stability of the device SGMCS-45E3B11.
Feature tracking control.
Even the lower mechanical properties, but also the characteristics of the mechanical recovery,
Make the mechanical properties of the control action, thereby reducing the time to adjust the timeEquipped with DeviceNet communication function type servo unit (servo controlled power supply drive type)
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC200V SGMCS-45E3B11.
Interface: instruction selection and installation (rotary type servo motor).
Matching (hardware): base mounting type (standard).
Matching (software): standard.
Matching (parameter): standard.
Optional modules: DeviceNet module (servo control power driver) + full closed loop module.
Communication specifications for DeviceNet based on open field network.
The combination of the DeviceNet controller and the V can be used to implement motion control in a simple way.
Can make use of the city''s rich DeviceNet support software.
Can use the upper controller to manage the servo information.
Through the network from the host controller to monitor the running status of the servo drive, alarm information.
Using the upper controller to manage the servo information, which can improve the maintenance (shorten the debugging time, improve the efficiency of maintenance operations).
Save wiring, reduce the cost and improve the reliability.
Because the upper controller and the servo unit arre connected through the communication network, the connection is greatly saved SGMCS-45E3B11.
Built in rich positioning function.
Can be from the upper controller (PLC or computer) to carry out a variety of simple positioning action.
Equipped with simple positioning, continuous rotation, and return to the origin of continuous rotary motion positioning, running and other rich positioning function SGMCS-45E3B11.


...More relevant models >>>>