LK Automation Limited
Brand:
Yaskawa
SGMCS-14M3A31 Direct drive servo motor
Yaskawa SGMCS-14M3A31 Manual And Instructions
SGMCS-14M3A31 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-14M3A31 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-14M3A31
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 14N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMCS-14M3A31 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-14M3A31 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-14M3A31
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 14N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor type SGMPH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit absolute value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft with screw key.
Optional parts: with DC90V brake.
Partial flat series: the need to install the servo motor in a small space SGMCS-14M3A31.
Flexible user system.
For you to build the best system to enrich the product line to support you SGMCS-14M3A31
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of SGMCS-14M3A31.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal SGMCS-14M3A31.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 1.8kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMCS-14M3A31.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMCS-14M3A31.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Power: 0.2kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit absolute value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft with screw key.
Optional parts: with DC90V brake.
Partial flat series: the need to install the servo motor in a small space SGMCS-14M3A31.
Flexible user system.
For you to build the best system to enrich the product line to support you SGMCS-14M3A31
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of SGMCS-14M3A31.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal SGMCS-14M3A31.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 1.8kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMCS-14M3A31.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMCS-14M3A31.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>