LK Automation Limited
Brand:
Yaskawa
SGMCS-07N3A11 Direct drive servo motor
Yaskawa SGMCS-07N3A11 Manual And Instructions
SGMCS-07N3A11 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-07N3A11 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-07N3A11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 7.0N.
Servo motor outside diameter size: 360mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMCS-07N3A11 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-07N3A11 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-07N3A11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 7.0N.
Servo motor outside diameter size: 360mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
High performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint SGMCS-07N3A11.
Function: pressure feedback control function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models SGMCS-07N3A11
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device SGMCS-07N3A11.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller SGMCS-07N3A11. Large capacity SGMVV type servo motor.
Rated output: 45KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenEquipped with DeviceNet communication function type servo unit (servo controlled power supply drive type)
Maximum applicable motor capacity: 2.0kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (rotary type servo motor).
Matching (hardware): paint.
Matching (software): standard.
Matching (parameter): standard.
Optional modules: DeviceNet module (servo control power driver) + full closed loop module.
Communication specifications for DeviceNet based on open field network.
The combination of the DeviceNet controller and the V can be used to implement motion control in a simple way.
Can make use of the city''s rich DeviceNet support software.
Can use the upper controller to manage the servo information.
Through the network from the host controller to monitor the running status of the servo drive, alarm information.
Using the upper controller to manage the servo information, which can improve the maintenance (shorten the debugging time, improve the efficiency of maintenance operations).
Save wiring, reduce the cost and improve the reliability.
Because the upper controller and the servo unit arre connected through the communication network, the connection is greatly saved SGMCS-07N3A11.
Built in rich positioning function.
Can be from the upper controller (PLC or computer) to carry out a variety of simple positioning action.
Equipped with simple positioning, continuous rotation, and return to the origin of continuous rotary motion positioning, running and other rich positioning function SGMCS-07N3A11.
Maximum applicable motor capacity: 7.5kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint SGMCS-07N3A11.
Function: pressure feedback control function.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models SGMCS-07N3A11
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device SGMCS-07N3A11.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller SGMCS-07N3A11. Large capacity SGMVV type servo motor.
Rated output: 45KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenEquipped with DeviceNet communication function type servo unit (servo controlled power supply drive type)
Maximum applicable motor capacity: 2.0kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (rotary type servo motor).
Matching (hardware): paint.
Matching (software): standard.
Matching (parameter): standard.
Optional modules: DeviceNet module (servo control power driver) + full closed loop module.
Communication specifications for DeviceNet based on open field network.
The combination of the DeviceNet controller and the V can be used to implement motion control in a simple way.
Can make use of the city''s rich DeviceNet support software.
Can use the upper controller to manage the servo information.
Through the network from the host controller to monitor the running status of the servo drive, alarm information.
Using the upper controller to manage the servo information, which can improve the maintenance (shorten the debugging time, improve the efficiency of maintenance operations).
Save wiring, reduce the cost and improve the reliability.
Because the upper controller and the servo unit arre connected through the communication network, the connection is greatly saved SGMCS-07N3A11.
Built in rich positioning function.
Can be from the upper controller (PLC or computer) to carry out a variety of simple positioning action.
Equipped with simple positioning, continuous rotation, and return to the origin of continuous rotary motion positioning, running and other rich positioning function SGMCS-07N3A11.
...More relevant models >>>>