LK Automation Limited
Brand:
Yaskawa
SGMAV-08ADA2E Ultra low inertia servo motor
Yaskawa SGMAV-08ADA2E Manual And Instructions
SGMAV-08ADA2E Setup Rotational MotorCommand Manual
Yaskawa SGMAV-08ADA2E Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-08ADA2E
Sigma -V series servo motor SGMAV.
Rated output: 0.75KW (750W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMAV-08ADA2E Setup Rotational MotorCommand Manual
Yaskawa SGMAV-08ADA2E Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-08ADA2E
Sigma -V series servo motor SGMAV.
Rated output: 0.75KW (750W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 5kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Matching (hardware): paint.
With the latest technology to pursue the use of convenience.
The use of new non adjustment function, no need to adjust SGMAV-08ADA2E.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed SGMAV-08ADA2E
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start.
Achieve a high response 1kHz above.
Equipped with a new advanced automatic tuning function SGMAV-08ADA2E.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control.Servo motor type SGMAH (speed: 3000r/min).
Power: 0.2kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with key SGMAV-08ADA2E.
Optional parts: no brake oil seal.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1/3, to achieve a good response.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop / control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance。Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMAV-08ADA2E.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMAV-08ADA2E.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Maximum applicable motor capacity: 5kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Matching (hardware): paint.
With the latest technology to pursue the use of convenience.
The use of new non adjustment function, no need to adjust SGMAV-08ADA2E.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed SGMAV-08ADA2E
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start.
Achieve a high response 1kHz above.
Equipped with a new advanced automatic tuning function SGMAV-08ADA2E.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control.Servo motor type SGMAH (speed: 3000r/min).
Power: 0.2kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with key SGMAV-08ADA2E.
Optional parts: no brake oil seal.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1/3, to achieve a good response.
The parameter setting and maintenance time is shortened.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanical characteristics.
Then use the main loop / control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance。Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMAV-08ADA2E.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMAV-08ADA2E.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>