LK Automation Limited
Brand:
Yaskawa
SGMAV-06A3A6S Ultra low inertia servo motor
Yaskawa SGMAV-06A3A6S Manual And Instructions
SGMAV-06A3A6S Setup Rotational MotorSetting Manual
Yaskawa SGMAV-06A3A6S Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-06A3A6S
Sigma -V series servo motor SGMAV.
Rated output: 0.6kw (600W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMAV-06A3A6S Setup Rotational MotorSetting Manual
Yaskawa SGMAV-06A3A6S Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-06A3A6S
Sigma -V series servo motor SGMAV.
Rated output: 0.6kw (600W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Design sequence: A.
Hardware specifications: paint.
Interface: MECHATROLINK-III communication command type (linear servo motor).
Function: no deviation standard SGMAV-06A3A6S.
High performance sigma shaped -V-EX series.
2 models of high performance servo unit SGMAV-06A3A6S
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control SGMAV-06A3A6S. Sigma -V series servo motor SGMGV.
Rated output: 11kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed) SGMAV-06A3A6S.
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1000r/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1/10, with parallel key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alaarm can only turn off the main circuit power supply, easy to maintain SGMAV-06A3A6S.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the origginal product reduced by 1/2 SGMAV-06A3A6S.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC200V.
Design sequence: A.
Hardware specifications: paint.
Interface: MECHATROLINK-III communication command type (linear servo motor).
Function: no deviation standard SGMAV-06A3A6S.
High performance sigma shaped -V-EX series.
2 models of high performance servo unit SGMAV-06A3A6S
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control SGMAV-06A3A6S. Sigma -V series servo motor SGMGV.
Rated output: 11kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed) SGMAV-06A3A6S.
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1000r/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1/10, with parallel key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alaarm can only turn off the main circuit power supply, easy to maintain SGMAV-06A3A6S.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the origginal product reduced by 1/2 SGMAV-06A3A6S.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control.
...More relevant models >>>>