LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGDV8R4DE5A000000601 Equipment DeviceNet communication function type servo driver

Yaskawa SGDV8R4DE5A000000601 Product information and technical parameters:
Brand: Yaskawa
Name: Equipment DeviceNet communication function type servo driver
Model: SGDV8R4DE5A000000601
Equipped with DeviceNet communication function type servo unit (external power supply drive type)
Maximum applicable motor capacity: 2.0kw.
Power supply voltage: three phase AC400V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): base mounting type (standard).
Matching (software): standard.
Matching (parameter): standard.
Optional modules: DeviceNet module (external power driver) + full closed loop module.
Communication specifications for DeviceNet based on open field network.
The combination of the DeviceNet controller and the V can be used to implement motion control in a simple way.
Can make use of the city''s rich DeviceNet support software.
Can use the upper controller to manage the servo information.
Through the network from the host controller to monitor the running status of the servo drive, alarm information.
Using the upper controller to manage the servo information, which can improve the maintenance (shorten the debugging time, improve the efficiency of maintenance operations).
Save wiring, reduce the cost and improve the reliability.
Because the upper controller and the servo unit are connected through the communication network, the connection is greatly saved.
Built in rich positioning function.
Can be from the upper controller (PLC or computer) to carry out a variety of simple positioning action.
Equipped with simple positioning, continuous rotation, and return to the origin of continuous rotary motion positioning, running and other rich positioning function.

Full closed loop module.
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard) SGDV8R4DE5A000000601.
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGDV8R4DE5A000000601
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response SGDV8R4DE5A000000601.
External encoder capable of corresponding high resolution (linear grating). Sigma -V series servo motor SGMSV.
Rated output: 7.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake) SGDV8R4DE5A000000601.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLow inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 2.5kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 7770 thousand \/rev pulse) SGDV8R4DE5A000000601.
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
IIt is helpful to the servo performance of ultra high speed and ultra precision control SGDV8R4DE5A000000601. most
To limit the performance of the device to solve the problem


...More relevant models >>>>
Related download