LK Automation Limited
Brand:
Yaskawa
SGDV2R8F21A000000001 Full closed loop servo system
Yaskawa SGDV2R8F21A000000001 Product information and technical parameters：
Brand: Yaskawa
Name: Full closed loop servo system
Model: SGDV2R8F21A000000001
Full closed loop module.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: base mounting type (standard).
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating).
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGDV2R8F21A000000001 SGDV2R8F21A000000001
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGDV2R8F21A000000001.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGDV2R8F21A000000001. Sigma -V series servo motor SGMJV.
Rated output: 0.75KW (750W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: no matching.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13/20 bit).
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installatiion method: flange type SGDV2R8F21A000000001.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew) SGDV2R8F21A000000001.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGDV2R8F21A000000001 SGDV2R8F21A000000001
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGDV2R8F21A000000001.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly SGDV2R8F21A000000001. Sigma -V series servo motor SGMJV.
Rated output: 0.75KW (750W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: no matching.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13/20 bit).
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installatiion method: flange type SGDV2R8F21A000000001.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew) SGDV2R8F21A000000001.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation.
...More relevant models >>>>
Related download