LK Automation Limited
Brand:
Yaskawa
SGDV-370D25A020000 Servo driver for linear servo motor
Yaskawa SGDV-370D25A020000 Product information and technical parameters：
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-370D25A020000
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Optional (hardware): DB resistance external type.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGDV-370D25A020000 SGDV-370D25A020000
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenDual axis servo drive SGD7W SGDV-370D25A020000.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Japanese production, interface is HMI connector).
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Dual axis servo unit (200W x 2 axis to 1kW x 2 axis) SGDV-370D25A020000.
Speed frequency response 1.6kHz.
Enhanced vibration suppression.
Gain adjustment without servo
YASKAWA created the "free adjustment function", the maximum load at 30 times the action does not produce vibration.
In addition, even if the action is changed, the action is stable.
Can be used in harsh environment and energy saving servo.
Can successfully build the best system in the worldSigma -V series servo motor SGMSV.
Rated output: 2.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat rresistance grade: F SGDV-370D25A020000.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDV-370D25A020000.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGDV-370D25A020000 SGDV-370D25A020000
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenDual axis servo drive SGD7W SGDV-370D25A020000.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Japanese production, interface is HMI connector).
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Dual axis servo unit (200W x 2 axis to 1kW x 2 axis) SGDV-370D25A020000.
Speed frequency response 1.6kHz.
Enhanced vibration suppression.
Gain adjustment without servo
YASKAWA created the "free adjustment function", the maximum load at 30 times the action does not produce vibration.
In addition, even if the action is changed, the action is stable.
Can be used in harsh environment and energy saving servo.
Can successfully build the best system in the worldSigma -V series servo motor SGMSV.
Rated output: 2.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat rresistance grade: F SGDV-370D25A020000.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDV-370D25A020000.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>