LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGDV-210D15A Servo driver for linear servo motor
Yaskawa SGDV-210D15A Manual And Instructions
SGDV-210D15A MECHATROLINK-II CommandsUSER'S MANUAL
SGDV-210D15A Design and MaintenanceUSER'S MANUAL

Yaskawa SGDV-210D15A Product information and technical parameters:
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-210D15A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Servo motor type SGMPH (speed: 3000r/min).
Power: 0.1kw.
Power supply voltage: single phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with DC24V brake.
Partial flat series: the need to install the servo motor in a small space SGDV-210D15A.
Flexible user system.
For you to build the best system to enrich the product line to support you SGDV-210D15A
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedNo speed reducer in inertia, high speed servo motor type SGM7J (rated speed 3000r\/min) SGDV-210D15A.
Rated output: 400W.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: C.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with oil seal SGDV-210D15A.
Cantilever state and moment of inertia.
After the change, can still maintain stable action.
Improvement of responsiveness.
Without adjustment, it can be achieved in the past about 2 times the response.
Improvement of stability.
The action is still stable for the presence of load fluctuations.
No gain adjustment.
Zero tuning time to ensure performance.
Protection system from the impact of temperature anomalies.
Servo unit and servo motor equipped with temperature sensor.
Monitor the temperature of the product directly through the sensor, as soon as possible to detect and prevent failure.
In addition, the temperature state of the system can be monitored by the machine controller, which is safe and secureLarge capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGDV-210D15A.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen


...More relevant models >>>>