LK Automation Limited
Brand:
Yaskawa
SGDH-75AE High performance servo driver
Yaskawa SGDH-75AE Manual And Instructions
SGDH-75AE datasheetPDF datasheet
SGDH-75AE AC Servodrive (400 V, 22 to 55 kW) Installation Guide
SGDH-75AE Manual
Yaskawa SGDH-75AE Product information and technical parameters：
Brand: Yaskawa
Name: High performance servo driver
Model: SGDH-75AE
Type: SGDH type drive.
Capacity: 7.5kw.
Voltage: three phase 200V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data.
...More relevant models >>>>
SGDH-75AE datasheetPDF datasheet
SGDH-75AE AC Servodrive (400 V, 22 to 55 kW) Installation Guide
SGDH-75AE Manual
Yaskawa SGDH-75AE Product information and technical parameters：
Brand: Yaskawa
Name: High performance servo driver
Model: SGDH-75AE
Type: SGDH type drive.
Capacity: 7.5kw.
Voltage: three phase 200V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data.
Servo motor type SGMPH (speed: 3000r/min).
Power: 0.4kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space SGDH-75AE.
Flexible user system.
For you to build the best system to enrich the product line to support you SGDH-75AE
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGDH-75AE. SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 16N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter size of the servo motor is marked as N and M SGDH-75AE.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type SGDH-75AE.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDH-75AE.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Power: 0.4kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space SGDH-75AE.
Flexible user system.
For you to build the best system to enrich the product line to support you SGDH-75AE
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGDH-75AE. SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 16N.
Servo motor outside diameter size: 280mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter size of the servo motor is marked as N and M SGDH-75AE.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type SGDH-75AE.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDH-75AE.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>