LK Automation Limited
Brand:
Yaskawa
SGDH-10AE High performance servo driver
Yaskawa SGDH-10AE Manual And Instructions
SGDH-10AE datasheetPDF datasheet
SGDH-10AE AC Servodrive (400 V, 22 to 55 kW) Installation Guide
SGDH-10AE Hardware Manual
Yaskawa SGDH-10AE Product information and technical parameters：
Brand: Yaskawa
Name: High performance servo driver
Model: SGDH-10AE
Type: SGDH type drive.
Capacity: 1.0kw.
Voltage: three phase 200V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data.
...More relevant models >>>>
SGDH-10AE datasheetPDF datasheet
SGDH-10AE AC Servodrive (400 V, 22 to 55 kW) Installation Guide
SGDH-10AE Hardware Manual
Yaskawa SGDH-10AE Product information and technical parameters：
Brand: Yaskawa
Name: High performance servo driver
Model: SGDH-10AE
Type: SGDH type drive.
Capacity: 1.0kw.
Voltage: three phase 200V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data.
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 15Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDH-10AE SGDH-10AE
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMGV SGDH-10AE.
Rated output: 7.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake) SGDH-10AE.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationNo speed reducer in inertia, high speed servo motor type SGM7J (rated speed 3000r\/min).
Rated output: 50W.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: C.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with oil seal.
Cantilever state and moment of inertia.
After the change, can still maintain stable action.
Improvement of responsiveness.
Without adjustment, it can be achieved in the past about 2 times the response.
Improvement of stability.
The action is still stable for the presence of load fluctuations.
No gain adjustment.
Zero tunning time to ensure performance SGDH-10AE.
Protection system from the impact of temperature anomalies.
Servo unit and servo motor equipped with temperature sensor.
Monitor the temperature of the product directly through the sensor, as soon as possibble to detect and prevent failure SGDH-10AE.
In addition, the temperature state of the system can be monitored by the machine controller, which is safe and secure
Rated speed: 1500r\/min.
Power: 15Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDH-10AE SGDH-10AE
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSigma -V series servo motor SGMGV SGDH-10AE.
Rated output: 7.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC90V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake) SGDH-10AE.
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationNo speed reducer in inertia, high speed servo motor type SGM7J (rated speed 3000r\/min).
Rated output: 50W.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: C.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with oil seal.
Cantilever state and moment of inertia.
After the change, can still maintain stable action.
Improvement of responsiveness.
Without adjustment, it can be achieved in the past about 2 times the response.
Improvement of stability.
The action is still stable for the presence of load fluctuations.
No gain adjustment.
Zero tunning time to ensure performance SGDH-10AE.
Protection system from the impact of temperature anomalies.
Servo unit and servo motor equipped with temperature sensor.
Monitor the temperature of the product directly through the sensor, as soon as possibble to detect and prevent failure SGDH-10AE.
In addition, the temperature state of the system can be monitored by the machine controller, which is safe and secure
...More relevant models >>>>