LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGM7A-A5A7A6C Low inertia, high speed servo motor
Yaskawa SGM7A-A5A7A6C Manual And Instructions
SGM7A-A5A7A6C datasheetPDF datasheet
SGM7A-A5A7A6C INSTRUCTION SHEET

Yaskawa SGM7A-A5A7A6C Product information and technical parameters:
Brand: Yaskawa
Name: Low inertia, high speed servo motor
Model: SGM7A-A5A7A6C
Low inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 50W.
Power supply voltage: AC200V.
Serial encoder: 24 bit absolute value type.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse).
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problem

Sigma -V series servo motor SGMSV.
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Super power rate.
Variety is complete (1 SGM7A-A5A7A6C. 0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) SGM7A-A5A7A6C
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type SGM7A-A5A7A6C.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLarge capacity SGMVV type servo motor SGM7A-A5A7A6C.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSecurity module.
Maximum applicable motor capacity: 3.0kw.
Power supply voltage: three phase AC200V.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional module: security module.
European EC standards: Based on the integration of mechanical instructions standard ISO13849-1 EN,
Security module with individual standard 61800-5-2 IEC specified security function.
Through the combination of the SGDV servo unit, the best safety design of the mechanical system is realized.
Suitable for AC servo drive, with the following safety features specified in the international standard IEC61800-5-2 (Japan''s first).
Can easily achieve the best security design of mechannical systems SGM7A-A5A7A6C.
Torque Off Safe (STO)
Stop Safe 1 (SS1)
Stop Safe 2 (SS2)
Limited Speed Safely (SLS)
Equipped with 2 security functions, can be set (distribution) security functions.
In addition, the monitoring time and other itemms can be changed through the parameter SGM7A-A5A7A6C.
With the use of the servo unit with a security module, so that the system can be simplified and miniaturized.


...More relevant models >>>>