LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGD7S-3R8A20A001 Single axis servo driver
Yaskawa SGD7S-3R8A20A001 Manual And Instructions
SGD7S-3R8A20A001 datasheetPDF datasheet
SGD7S-3R8A20A001 Communications ReferencesInstruction Guide
SGD7S-3R8A20A001 MECHATROLINK-III CommunicationsINSTRUCTION SHEET

Yaskawa SGD7S-3R8A20A001 Product information and technical parameters:
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-3R8A20A001
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.5kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ᥹఼
Design sequence: A.
Hardware purchase: rack installation specifications.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown

Servo motor type SGMPH (speed: 3000r\/min).
Power: 0.2kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit absolute value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft with screw.
Optional parts: with oil seal.
Partial flat series: the need to install the servo motor in a small space SGD7S-3R8A20A001.
Flexible user system.
For you to build the best system to enrich the product line to support you SGD7S-3R8A20A001
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedLarge capacity SGMVV type servo motor SGD7S-3R8A20A001.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw) SGD7S-3R8A20A001.
Optional parts: keep the brake (DC90V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenDC power input servo unit type SGDV.
Maximum applicable motor capacity: 11W.
Power supply voltage: DC48V.
Interface: analog voltage command type (rotary servo motor).
Design sequence: A.
Pursuit of light weight.
The compact and light weight of the driver can be effectively used in a limited space, and the space of the control cabinet and the device can be used as a contribution.
Using DC power input.
Servo can use battery driven, small size, superior performance,
Can further improve the clean room robot, AGV (unmanned vehicle), such as the level of battery driven transport system.
In addition, the control power supply and the main circuit power supply are independent of the power supply system,
The main circuit power supply can be cut off only when an alarm occurs, and the fault diagnosis can be easily carried out.
Main circuit power supply can use DC24V and DC48V power supply.
When using DC48V power supply, can further improve the motor speed characteristics"
Control power is only DC24V. The improvement of the characteristic is different from the motor. For more details, please refer to the "torque speed characteristics" of the combined motor.
With the latest technology to pursue high performance and ease of use
Using the new advanced automatic tuning function, can be in a short period of time to thhe user system for the best setting SGD7S-3R8A20A001.
The model tracking control and vibration suppression of the shaking of the device is provided with a shortened positioning time,
The ability of anti load fluctuation to compensate the friction coompensation,
The most suitable for the device to start operation and load fluctuations in the various uses of the new type of non functional adjustment SGD7S-3R8A20A001.


...More relevant models >>>>