LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGD7W-2R8A30A Dual axis servo drive
Yaskawa SGD7W-2R8A30A Manual And Instructions
SGD7W-2R8A30A datasheetPDF datasheet

Yaskawa SGD7W-2R8A30A Product information and technical parameters:
Brand: Yaskawa
Name: Dual axis servo drive
Model: SGD7W-2R8A30A
Dual axis servo drive SGD7W.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (interface is RJ-45 connector).
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Dual axis servo unit (200W x 2 axis to 1kW x 2 axis).
Speed frequency response 1.6kHz.
Enhanced vibration suppression.
Gain adjustment without servo
YASKAWA created the "free adjustment function", the maximum load at 30 times the action does not produce vibration.
In addition, even if the action is changed, the action is stable.
Can be used in harsh environment and energy saving servo.
Can successfully build the best system in the world

Servo motor type SGMPH (speed: 3000r\/min).
Power: 0.1kw.
Power supply voltage: single phase AC100V.
Serial encoder: 16 bit relative value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC24V brake.
Partial flat series: the need to install the servo motor in a small space SGD7W-2R8A30A.
Flexible user system.
For you to build the best system to enrich the product line to support you SGD7W-2R8A30A
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of SGD7W-2R8A30A.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 2.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key SGD7W-2R8A30A.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor type SGMAH (speed: 3000r\/min).
Power: 0.4kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting aand maintenance time is shortened SGD7W-2R8A30A.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanicall characteristics SGD7W-2R8A30A.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance


...More relevant models >>>>