LK Automation Limited LK Automation Limited
Brand: Yaskawa
Go Back >> Product Catalogues
SGD7S-120A20A Single axis servo driver
Yaskawa SGD7S-120A20A Manual And Instructions
SGD7S-120A20A datasheetPDF datasheet
SGD7S-120A20A Communications ReferencesHardware Manual
SGD7S-120A20A MECHATROLINK-III CommunicationsINSTRUCTION SHEET

Yaskawa SGD7S-120A20A Product information and technical parameters:
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-120A20A
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 1.5kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ᥹఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown

Sigma -V series servo motor SGMGV.
Rated output: 450W (0.45KW).
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V) SGD7S-120A20A.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake) SGD7S-120A20A
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above SGD7S-120A20A.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection SGD7S-120A20A.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationEquipped with DeviceNet communication function type servo unit (servo controlled power supply drive type)
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC400V.
Interface: instruction selection and installation (linear servo motor).
Matching (hardware): paint.
Matching (software): standard.
Matching (parameter): standard.
Optional modules: DeviceNet module (servo control power driver) + full closed loop module.
Communication specifications for DeviceNet based on open field network.
The combination of the DeviceNet controller and the V can be used to implement motion control in a simple way.
Can make use of the city''s rich DeviceNet support software.
Can use the upper controller to manage the servo information.
Through the network from the host controller to monitor the running status of the servo drive, alarm information.
Using the upper controller to manage the servo information, which can improve the maintenance (shorten the debugging time, improve the efficiency of maintenance operations).
Save wiring, reduce the cost and improve the reliability.
Because the upper controller and the servo unit arre connected through the communication network, the connection is greatly saved SGD7S-120A20A.
Built in rich positioning function.
Can be from the upper controller (PLC or computer) to carry out a variety of simple positioning action.
Equipped with simple positioning, continuous rotation, and return to the origin of continuous rotary motion positioning, running and other rich positioning function SGD7S-120A20A.


...More relevant models >>>>