LK Automation Limited LK Automation Limited
Download Sort: Yaskawa
Home >> Manual Download
SGMCS-08MDA11 USER'S MANUAL (Setup Rotational Motor)
Product model: SGMCS-08MDA11
Name: AC Servo Drives
Brand: Yaskawa
Sort: Setup Rotational Motor USER'S MANUAL
File language: English
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7 SGMCS-08MDA11 USER'S MANUAL. 0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit) SGMCS-08MDA11
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type SGMCS-08MDA11 USER'S MANUAL.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLarge capacity SGMVV type servo motor SGMCS-08MDA11 USER'S MANUAL.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC24V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen.









Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (rotary servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Puulse generator for D/A converter or position instruction without speed / torque command SGMCS-08MDA11 Manual.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMCS-08MDA11 Manual.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Related products
Yaskawa
Direct drive servo motor
SGMCS-35EDB11
Yaskawa Direct drive servo motor SGMCS-35EDB11
SGMCS small capacity type of direct driv
Yaskawa
Direct drive servo motor
SGMCS-35BDC41
Yaskawa Direct drive servo motor SGMCS-35BDC41
SGMCS small capacity type of direct driv
Yaskawa
Direct drive servo motor
SGMCS-17N3A31
Yaskawa Direct drive servo motor SGMCS-17N3A31
SGMCS small capacity type of direct driv
Yaskawa
Direct drive servo motor
SGMCS-10NDA11
Yaskawa Direct drive servo motor SGMCS-10NDA11
SGMCS small capacity type of direct driv